色呦呦网址在线观看,久久久久久久久福利精品,国产欧美1区2区3区,国产日韩av一区二区在线

Surface roughness is an indicator used to measure the degree of surface micro-irregularities, and it is commonly annotated on mechanical drawings with roughness symbols. The types of roughness symbols include surface roughness symbols, roughness codes, and additional descriptions. The following is a detailed introduction to the types of roughness annotations.

Figure 1. Schematic of roughness surface profile hatching.

Surface Roughness Symbol

4 Points of Machining Surface Roughness You Need to Know 1

4 Points of Machining Surface Roughness You Need to Know 2

a?、a?— symbols and values for the roughness height

parameters (unit is μm);

b — machining requirements, plating, coating, surface treatment, or other descriptions;

c — sampling length (in millimeters) or waviness (in micrometers);

d — symbol for the direction of the machining texture;

e — machining allowance (in millimeters);

f — roughness spacing parameter (in millimeters) or profile support length ratio.

?Other Annotation Descriptions

  • Sampling Length: The length range selected when measuring roughness, used to calculate roughness parameters.
  • Evaluation Length: The total sum of the sampling lengths, used to assess surface roughness.
  • Machining Method: Indicates the machining method by which the surface roughness is achieved, such as turning, grinding, etc.
  • Other Requirements: For example, surface treatment (such as sandblasting, polishing, etc.), texture direction, etc.
Machining Texture Requirements
Machining Texture Requirements

4 Points of Machining Surface Roughness You Need to Know 34 Points of Machining Surface Roughness You Need to Know 4

Roughness Code

Arithmetic Mean Roughness Ra

Arithmetic mean roughness is the most commonly used roughness parameter, representing the arithmetic average of the absolute values of the profile peaks and valleys within the sampling length. When selecting the reference length in the direction of the mean line from the roughness curve, using the direction of the mean line of the selected part as the X-axis and the direction of the vertical magnification as the Y-axis, if the roughness curve is represented as y=f(x), the value obtained from the following formula, when expressed in micrometers (μm), is called the arithmetic mean roughness Ra.

4 Points of Machining Surface Roughness You Need to Know 5

Arithmetic Mean Roughness Ra

Note: The arithmetic mean roughness Ra is the most commonly used expression for roughness. Unless otherwise specifically noted, roughness generally refers to Ra.

From the roughness curve, a reference length is selected in the direction of the mean line. From the values measured in the direction of the vertical magnification from the mean line of the selected part, the sum of the average absolute values of the peak elevations (Yp) from the highest peak to the fifth peak and the average absolute values of the valley elevations (Yv) from the lowest valley to the fifth valley is calculated. This sum is referred to as the value expressed in micrometers (μm).

Ten-Point Average Roughness Rz
Ten-Point Average Roughness Rz

Maximum Height Ry

The maximum profile height, which represents the vertical distance between the highest profile peak and the deepest valley within the sampling length. From the roughness curve, a reference length is selected in the direction of the mean line. The interval between the peak line and the valley line of the selected part is measured in the direction of the vertical magnification of the roughness curve, and this value is called the micrometer value (μm).

Note: When determining Ry, the reference length should be selected from a section of the curve that is free of cracks and extreme peaks and valleys.

Maximum Height Ry
Maximum Height Ry

Labeling Example

Label the upper limit value of Ra

4 Points of Machining Surface Roughness You Need to Know 6

  • Control the surface roughness to within 25μm by any means.
  • Control the surface roughness to within 6.3μm by material removal methods.
  • Control the surface roughness to within 25μm without removing material.

Label the direction of the machining texture

4 Points of Machining Surface Roughness You Need to Know 7

Note: The direction of the machined tool texture is perpendicular to the projection plane marked with symbols.

Label the upper and lower limits of Ra

4 Points of Machining Surface Roughness You Need to Know 8

Control the surface roughness to a minimum of 1.6μm and a maximum of 6.3μm by removing material. Generally, the upper and lower limit values are marked for oil seal installation holes, as roughness that is too large or too small can affect the sealing effect of the oil seal.

Label the machining methodsurface roughness

Marking Machining Method

Attention Points Marking Position: The roughness symbol is usually annotated above or below the dimension line, close to the surface being marked.

Direction Guide Line: The direction guide line should point towards the surface being marked and be parallel or perpendicular to the surface.

Value Unit: The chropowato?? values are typically expressed in micrometers (μm).

Dodaj komentarz

Twój adres email nie zostanie opublikowany. Pola, których wype?nienie jest wymagane, s? oznaczone symbolem *

比如县| 夏河县| 祥云县| 江源县| 青海省| 三门峡市| 通许县| 赤水市| 惠来县| 长春市| 孝义市| 广丰县| 祁连县| 青河县| 天长市| 剑阁县| 昌平区| 玉树县| 略阳县| 潍坊市| 农安县| 安吉县| 嘉荫县| 延庆县| 灵丘县| 峨山| 嘉善县| 富裕县| 郁南县| 平山县| 康定县| 邵东县| 鹤岗市| 新晃| 阳曲县| 长宁县| 策勒县| 江永县| 柳河县| 沅江市| 临城县|